APPLICATION OF INTEGRATED SEMI-HOT STAMPING TECHNOLOGY FOR THE PRODUCTION OF HUB AND FLANGE TYPE PARTS

The main part of the cost of machine-building products is the cost of the metal used to manufacture the part. In order to reduce the amount of metal waste and improve the quality of stamped forgings, new technologies have been developed for the production of standard machine-building parts such as "hub" and "flange" based on the integrated technology of semi-hot stamping from a ball blank. According to the factory technology, the parts in question are produced by hot-dip stamping: metal is divided into cylindrical blanks for subsequent stamping by cutting on press shears, the weight spread of such blanks is 10 ‒ 12 %; metal is heated for stamping to a temperature of 1150 – 1200 °C, when heated to such temperatures, scale forms on the surface of the workpiece; stamping in open dies with pre-laying of a cylindrical billet and clipping of a chip. According to the developed technologies, the initial blank is an accurate ball blank obtained by separation in cross-screw rolling mills, the mass spread of which does not exceed 8 %. The heating temperature for stamping is reduced and is in the range of 850 ‒ 900 °C, when heated to temperatures of semi-hot stamping, scale does not form on the surface of the blank; stamping is carried out in one the transition is in a closed stamp. Comparative schemes of manufacturing parts according to factory and developed technologies are presented. The conducted studies have shown that the use of integrated technology allows to obtain accurate forgings by weight with minimal allowances for subsequent machining in fewer operations and save up to 25 % of the metal from the initial mass of the workpiece.

1. Favi C., Campi F., Mandolini M., Germani M., Mar-tinelli I. Key features and novel trends for developing cost engineering methods for forged components: a systematic literature review. The International Journal of Advanced Manufacturing Technology. 2021;117:2601‒2625.

2. https://doi.org/10.1007/s00170-021-07611-4.

3. Peretyatko, V.N., Bakhaev A.V., Filippova M.V., Vakhman S.A. Stamping axisymmetric forgings. Steel in Translation. 2009;39(4):300–301. https://doi.org/10.3103/S0967091209040032.

4. GOST 7524 – 2015. Steel grinding balls for ball mills. (Technical conditions). Moscow: Publishing house of standards, 2016:20. (In Russ.).

5. Chila P., Pater Z., Tomczak J., Chila P. Numerical analisis of rolling process for producing steel balls us-ing helical rolls. Archives of Metallurgy and Materials. 2016;61(2):485–492.

6. https://doi.org/10.1515/amm-2016-0085

7. Ren X., Liu Y. Study on the influence of de-forming velocity on steel ball quality based on DEFORM. Applied Mechanics and Materials. 2012;117-119:1806‒1809. https://doi.org/10.4028/www.scientific.net/AMM.117-119.1806

8. Pater Z. etc. Experimental and numerical analysis of helical-wedge rolling process for producing steel balls. International Journal of Machine Tools and Manufac-ture. 2013;67:1–7.

9. https://doi.org/10.1016/j.ijmachtools.2012.12.006

10. Schwartz D.L., Semenov A.A., Galim'yanov I.K. Computer modeling of two-pass rolling in the production of grinding balls with a diameter of 100 mm from alloy steels. Metallurgist. 2022;1:79–84. https://doi.org/10.52351/00260827_2022_01_79

11. Du S., Ren X. Analysis of factors influencing the skew rolling ball quality. Materials. 2013;12;9:248–250. https://doi.org/10.52351/00260827_2013_01_32

12. Pater Z. Analysis of helical rolling process of balls formed from a head of a scrapper rai. Ad-vances in Science and Technology Research Journal. 2016;10(30):110–114.

13. https://doi.org/10.12913/22998624/62702.

14. Shvarts D.L., Galim’yanov I.K. Improvment of a double-helical roll pass design for rolling 100-mm grinding balls. Metallurgist. 2022;66(3-4):422–432. https://doi.org/10.1007/s11015-022-01343-w

15. Rubtsov V.Yu., Shchevchenko O.I., Alypov P.A., Lebedev V.A. Grinding balls of high accuracy. News of higher educational institutions. Volga region. Engineering sciences. 2020;2(54):86–96. (In Russ.). https://doi.org/10.21685/2072-3059-2020-2-9

16. Temlyantsev M.V., Korotkov S.G., Tem-lyantseva E.N. Development of the theory and practice of low-oxidizing and low-decarburizing steel heating technologies. Bul-letin of the Siberian State Industrial University. 2019;3(29):20‒24. (In Russ.).

17. Lyalin V.M. Semi-hot stamping of the "valve" part in split dies. Bulletin of Tula State University. Technical sciences. 2013;6-2:263–269. (In Russ.).

18. Zhelezkov O.S., Galiakhmetov T.Sh., Lizov S.B. Search for rational technologies for the production of hexagon-head bolts from stain-less steel based on an integrated criteria ap-proach. Mechanical equipment of metallurgical plants. 2022;1(18):55–60. (In Russ.).

19. Filippova M. V., Peretyatko V. N., Tem-lyantsev M. V. Development and implementa-tion of energy- and resource-saving technolo-gies for metal forming. Novosibirsk: SB RAS, 2016:266. (In Russ.).

20. Filippova M.V., Peretyatko V.N., Prudkiy E.E., Temlyantsev M.V., Nikitin A.G. Com-plex technology of stemping details "hub" from ball blank. IOP Conference Series: Mate-rials Science and Engineering. 2018. https://doi.org/10.1088/1757-899X/411/1/012083.

21. Filippova M.V., Prudkiy E.E., Peretyatko V.N. Flash-free stamping of the “hub” part from a spherical blank. In: Russian Science in the Modern World. Collection of articles from the XI International Scientific and Practical Con-ference. 2017:58–61. (In Russ.).

22. Filippova M.V., Smetanin S.V., Prudkiy E.E. Semi-hot volume stamping complex. In: Metal-lurgy: new technologies, management, innova-tions and quality. Proceedings of the All-Russian scientific and practical conference. Siberian State Industrial University. 2016:227–229. (In Russ.).

23. Filippova M.V., Smetanin S.V. Production of precise-weight ball blanks on cross-helical rolling mills. Rolling production (supplement to the journal "Technology of Metals"). 2025;22:32–40. (In Russ.).

24. Filippova M.V., Temlyantsev M.V., Peretyat`ko V.N., Prudkii E.E. Rolling of met-al ball. Steel in Translation. 2017;47:435–439. https://doi.org/10.3103/S0967091217070038

25. Filippova M.V., Prudkiy E.E., Bakhaev A.V. Modeling of stamping of the “flange” part from a spherical blank. In: Innovative Conven-tion “Kuzbass: Education, Science, InnovaInnovation”. Proceedings of the Innovation Convention. 2019:543–546. (In Russ.).